Coyote Lock Connectors

The Alignable Connector is attached to the lock in the desired location for prosthetic alignment, allowing the lock to remain in ideal lock alignment for easy engagement. A single lamination is done that incorporates the lock and the connector into the socket. The offset capability saves money by eliminating need for offset components, and saves time with a single lamination and easy component setup.

 

Coyote Air Lock CD103 fitted with a CD103AF Alignable Connector using a CD103MDI Multi-Direction Insert

Coyote Air Lock CD103 fitted with a CD103AF Alignable Connector using a CD103MDI Multi-Direction Insert

Coyote Air Lock CD103 fitted with a CD103AF Alignable Connector using a CD103SDI Multi-Direction Insert

CD111 One-Shot Connector example build using the Coyote Basalt Composite

CD103AF

CD103AF | Alignable Connector

Up to 0.6" of offset, 35g. Ideal for use with Air-Lock and Easy Off Locks. Can be glued to the lock in any offset position for fabrication into the socket, or keys directly onto locks when used with inserts. Eliminates need for offset components. For laminations or thermoforming. 265 lb weight limit.

CD111

CD111 | One-Shot Connector

Up to 0.6" offset, 44g. Connector with tie off ring for easier lay-ups. Lower profile than Alignable Connector. Can be glued to lock in desired location or keyed onto lock using inserts. For laminating only. 265 lb weight limit.

CD103MDI

CD103MDI | Multi-Direction Insert

Up to 0.33" offset in two directions. Installed into connector to allow connector to be keyed onto bottom of lock in centered position or offset in two directions. For laminations or thermoforming. Use with Alignable Connector or One-Shot Connector.

CD103SDI

CD103SDI | Single-Direction Insert

Up to 0.33" of offset in one direction. Installed into connector to allow connector to be keyed onto bottom of lock in centered position or offset in one direction. For laminations or thermoforming. Use with Alignable Connector or One-Shot Connector.

CD108 | Integrator

Standard size, fits most lower extremity limbs. Integrator glues to mould. Alignable Connector with or without inserts is keyed onto Integrator and both parts are fabricated into socket. 265 lb weight limit. Thermoforming or laminating. (2 3/8" diameter) (AK) (BK)

 

CD108S | Small Integrator

Smaller size for smaller limb shapes. 265 lb weight limit. Thermoforming or laminating. (2"diameter) (AK) (BK)

CD103PFF

CD103PFF | Pediatric Fast Four Connector

Pediatric 4-hole connector that keys directly onto center of lock. 100 lb weight limit.

CD103PAF

CD103PAF | Pediatric Alignable Connector

Can be used to offset the connector by up to 0.25". 100 lb weight limit.

 

CD115CF5 | 5 Degree AK Connector

Capable of up to 1.5” of Offset with 5 degrees of flexion angle. The 5 Degree AK Connector is used primarily with the Coyote Design Lanyard Lock CD118 but can be used with Coyote Design pin systems or other locks in combination with the Integrator. Can be glued to the lock in any offset position for fabrication into the socket. Eliminates the need for offset components. For lamination or thermoforming. 265 lb. weight limit.

CD119SC | Test Socket Connector

Cost affective connector designed specifically for Vivac check sockets.
Economical, cost effective, easy way to glue on a connector. Connects to standard four hole componentry with our new high strength bridging design.
Bonds well with Coyote Quick Adhesive.
11/16"height, 2 3/4" diameter, reusable.

CD106

CD106 | Alignment Coupler

Offset for ML and AP of 0.64". Easily installs on four hole connector. Easy to adjust with 3mm wrench. For fitting purposes only. 265 lb weight limit.

Coyote Quick Glue Adhesive

Great for any situation when you need something glued quickly and easily.